Skip to content
Features
MC700 is a universal motion controller for 1 to 4 axis, programmable for multiple motion applications by simple download of the corresponding function firmware
With the use of Matona's CT701 firmware, this unit provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool
Extremely smooth motion to protect mechanical solution, by self-optimizing polynomial speed transitions
High cutting accuracy, even during line acceleration and at high speeds
Programmable cosine-compensated speed profile
Special torque control features to master the impact load when cutting hard materials like stainless steel etc.
Special profile features to avoid deadlock between tool and material
Embedded virtual master axis (selectable)
Black-box unit for cabinet mounting
Remote control and communication facilities via external operator terminal, serial PC communication, PROFIBUS or optional via CANBUS (MC700/CI) etc.
Features
2 pulse inputs with format A, /A, B, /B, Z, /Z [HTL, RS422]
With an input frequency of up to 2 MHz
2 control inputs with format SIN+, SIN-, COS+, COS- [1 Vss] with an input frequency of up to 400 kHz
2 SSI inputs with format DATA+, DATA-, CLOCK+, CLOCK- up to 25 Bit, with SSI switching frequency of 100 Hz ... 1 MHz
2 scalable 14-bit analog inputs for ±10 V or 0/4 ... 20 mA
4 control inputs for PNP / NPN signals [10 ... 30 VDC]
4 fast interrupt inputs for PNP / NPN signals [10 ... 30 VDC]
1 pulse output with format A, /A, B, /B, Z, /Z [RS422]
4 control outputs with push-pull characteristic, short-circuit-proof [5 ... 30 VDC]
2 scalable 14-bit analog outputs for ±10 V or 0/4 ... 20 mA
Loop time approx. 250 µs
Power supply 18 ... 35 VDC
Snap-on housing for top-hat rail (according to EN 60715)
OnBoard interfaces: Ethernet / IP, RS232 / RS485, USB 2.0, CANopen, Modbus RTU
Optional Ethernet interfaces: EtherCAT, Ethernet / IP, Modbus TCP, Powerlink, PROFINET, SERCOS III
Optional Fieldbus interfaces (slave): CC-Link, DeviceNet, PROFIBUS
Operates with all 4-Q-drive systems, equipped with a standardized drive communication bus (e. g. SERCOS-II). Alternatively, ±10 V setpoint can be used
The controllers can be setup by an external operator terminal as well as HMI’s via standardized factory communication bus e.g. PROFINET
Setup via Windows operator software (free of charge)
Features
Very high-performance economical encoder
Low profile—25.4 mm height and 38 mm diameter
Thru-bore with sizes up to 10 mm
Simple, innovative flex mounting system (Global Mounting Standards)
Up to 12 pole commutation optional for brushless motor control
Features
Very high-performance economical encoder
Low profile—25.4 mm height and 38 mm diameter
Thru-bore with sizes up to 10 mm
Simple, innovative flex mounting system (Global Mounting Standards)
Up to 12 pole commutation optional for brushless motor control
Features
5mm Opto-ASIC encoder with a low profile (50.8mm)
Imperial bore sizes range from 0.625” to 1.125”
Metric bore sizes ranging from 6 mm to 28 mm
Single replacement solution for 50.8mm to 88.9mm encoders
Resolutions to 10,000 PPR, frequencies to 1 MHz
Versatile flexible mounting options
RoHS compliant
Corrosion-Resistant Option
Features
Low profile 30.3mm
Up to 12 pole commutation
Thru-bore and hollow-bore (blind) styles
Simple, innovative flexible mounting system
Incorporates Opto-ASIC technology
Features
Body: Precision Machined Aluminium
Cover: Precision Machined Aluminium (Powder Coated)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing - Rear: Single lip seal on the rear of cover
Protection: IP65
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM (Higher on request)
Torque: 2Ncm (typical)
Inertia: 100gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Body: Stainless Steel (316)
Cover: Stainless Steel (316)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing + Single lip seal
Rear: Single lip seal on the rear of the cover
Protection: (IP66 / IP67)
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM
Torque: 4Ncm (typical)
Inertia: 200gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Size 25 / 63.5mm Diameter (Hollow Shaft)
Up to 12 Pole Commutation Available
Thru Bore and Blind Bore Options
Simple, Innovative Flexible Mounting System
Incorporates Opto-ASIC Technology
Features
Thru-bore design for easy mounting
Bore options to 1.375" and 32mm
Incorporates Opto-ASIC technology
Resolutions to 4096 PPR
100° C operating temperature available
Features
Slim profile—only 34.5mm in depth
Thru-bore design for easy mounting
Incorporates Opto-ASIC technology
Resolutions to 4096 PPR
Bore options to 1.875" and 43mm
Features
Body: Precision Machined Aluminium
Cover: Precision Machined Aluminium (Powder Coated)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing
Rear: Single lip seal on the rear of the cover
Protection: IP65
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM (Higher on request)
Torque: 3Ncm (typical)
Inertia: 600gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Number of output pulses per revolution 5.000 - 500.000 ppr
Line number on disc (z) 5.000
Maximum shaft speed 8000 rpm
The permissible motion of the shaft
- axial: ± 1.00 mm
- radial: 0.02 mm
Accuracy (T1-period lines on disc in arc. sec) ± 0.05T1 arc. sec
Starting torque at 20°C ≤ 0.01 Nm
Rotor moment of inertia < 20x10-4 kgm2
Protection (housing) (IEC 529) IP64
Protection (shaft side) (IEC 529) IP64
Maximum weight without cable 0.8 kg
Operating temperature -20...+70°C
Storage temperature -30...+85°C
Maximum humidity (non-condensing) 98%
Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
Permissible shock (11 ms) ≤ 300m/s²
Features
Number of output pulses per revolution 100-108000 ppr
Maximum shaft speed 10000 rpm
The permissible motion of the shaft
- axial: ± 0.5 mm
- radial: ± 0.05 mm
Accuracy (T1-period lines on disc in arc. sec) ± 0.1T1 arc. sec
Starting torque at 20°C ≤ 0.025 Nm
Rotor moment of inertia < 1.5x10-4 kgm2
Protection (housing) (IEC 529) IP64
Protection (shaft side) (IEC 529) IP64
Maximum weight without cable 0.3 kg
Operating temperature -10...+70°C
Storage temperature -30...+80°C
Maximum humidity (non-condensing) 98%
Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
Permissible shock (5 ms) ≤ 1000 m/s²
Features
Standard Size 36mm package (1.42")
Durable magnetic technology
Multiturn absolute encoder (12-bit/39-bit)
SSI and CANopen communications
Proven new turns counting technology — no gears or batteries
Features
MC700 is a universal motion controller for 1 to 4 axes, which can be assigned any motion control functions by loading firmware. Together with the firmware BY701 (see firmware), this controller offers excellent synchronous functions for 1 - 4 axes.
The firmware offers all conceivable possibilities for the synchronization of drives, including the influence of phase position and the relative position between the drives and numerous index and print mark functions.
Optionally, a "physical master" or the built-in "virtual master axis" with programmable speeds and ramps can be used as the master drive.
The number of successive axes can be extended arbitrarily via a cascading output.
MC700 controllers can be operated via an external control terminal, serial interface or optional via CANBUS (MC700/CI). PC operator software is included.
PROFIBUS connection possible via gateway PB251 (see accessories)
Features
High level of external safety (Recognition of electrical or mechanical errors in the machinery/sensor systems/wirings etc.)
High level of internal safety (detection of internal errors and failures of the device components)
2 Pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
4 control inputs for PNP / NPN / Namur signals [10 ... 30 VDC]
6 logical inputs for PNP signals [10 ... 30 VDC]
Input frequency up to 500 kHz
4 fast transistor outputs with push-pull characteristics, short-circuit-proof [5 ... 30 VDC]
4 forced-guided redundant output relays with potential free change-over contact
Serial interface RS232 and RS485
Power supply 24 VAC and 17 ... 40 VDC
Compact norm panel housing
6 digits LED display with 15 mm height
Display range -199999 ... 999999
Setup by keys or PC via serial RS232 Interface
Dimension B x H x T = 110 x 48 x 140 mm (4,33 x 1,89 x 5,51")
Features
Suitable for display units with front dimensions 96 x 48 mm
(fits not to Profibus indicator PB340)
Protection class IP65
Features
To increase the protection class in dusty or wet environments, several types of protection caps are available for motrona units.
Some of the elastic and transparent plastic caps allow you to operate the keypad or to set the thumbwheel switches behind the cap, without removing it.
Features
Hollow Shaft Small Size
Resolution (Counts/Turn): 1,000∼12,000C/T
Output Phase: A, B, Z, EU, EV, EW Phase
Max Response Frequency: 200kHz
Supply Voltage: DC+5V
Consumption Current: 200mA Max
Output Form: Line Driver
Mounting Tolerance: Radial 0.05mm TIR Max, Axial 0.2mm Max, Shaft Runout 0.1°Max
Starting Torque: 9.8×10-3N⋅m (100gf⋅cm Max)
Protection: IP=40
Operating Temp. Range: -20∼+85°C
Vibration: 49m/s2(5G)
Shock: 980m/s2(100G)
Mass: 0.3kg Max
Page load link