Skip to content
-
Features
- 20-bit parallel input with format BCD, binary or Gray-Code
- Input frequency: fast encoder 5 kHz, auto-transmit / data logging 0.5 kHz
- 4 status outputs, with push-pull characteristics, short-circuit-proof [5 ... 30 VDC]
- Power supply 10 ... 30 VDC
- Snap-on housing for top-hat rail (according to EN 60715)
- Serial RS232 / RS485 interface
-
Features
- Pulse input with format A, B, Z [HTL] (10 ... 30 V)
- Input frequency max. 200 kHz
- Pulse output with format A, /A, B, /B, Z, /Z [RS422 / TTL]
- Power supply 5 VDC
- Converts HTL levels (A / B / Z) in TTL / RS422, incl. the inverted signals
- Converts also static/separate directional information into a dual channel A / B signal with a 90° phase shift
- Open print version with plastic snap-on housing for top-hat rail (according to EN 60715)
-
Features
- Pulse input with format A, /A, B, /B, Z, /Z [TTL / RS422]
- Input frequency max. 200 kHz
- Pulse output with format A, B, Z [HTL]
- Power supply 10 ... 30 VDC
- Converts TTL / RS422 signals (A, /A, B, /B, Z, /Z) in HTL format with an output level of 10 ... 30 VDC
- Generates additionally an A / B directional information with 90° phase shift‚ a static HIGH / LOW directional signal or separate directional pulses
- Open print version with plastic snap-on housing for top-hat rail (according to EN 60715)
-
Features
- 1 pulse input with format A, B, Z [HTL] or A, /A, B, /B, Z, /Z [RS422]
- Input frequency up to 500 kHz
- 1 pulse output with format A, /A, B, /B, Z, /Z [RS422, HTL]
- Power supply 5 ... 30 VDC
- Potential separation between input and output
- Possibility to convert A, B / 90 ° directional information into static directional signal and vice versa
- Connections on the input as well as on the output either via sub-D plugs or plug-in screw terminals (parallel connections)
- Snap-on housing for top-hat rail (according to EN 60715)
-
Features
- 1 connector Sub-D-9 (male)
- 1 connector Sub-D-9 (female)
- cable length 3 m (approx. 10 feet)
-
Features
- Support brackets with a snap mechanism for easy installation of panel housings onto a 35 mm DIN rail (according to EN 60715)
- Suitable for display units with front dimensions of 96 x 48 mm
-
Features
- Support brackets with a snap mechanism for easy installation of panel housings onto a 35 mm DIN rail (according to EN 60715)
- Suitable for display units with front dimensions of 96 x 96 mm
-
Features
- 1 encoder input with format SIN+, SIN-, COS+, COS-, REF+, REF- [1 Vss]
- Maximum sinus input frequency 500 kHz with max. 200 ns conversion time
- 4 signal outputs with format SIN+, SIN-, COS+, COS-, REF+, REF- [1 Vss]
- Power supply 17 ... 30 VDC
- Snap-on housing for top-hat rail (according to EN 60715)
-
Features
- USB cable for connection between PC and the Motrona unit UZ210
- Both connectors are type A
- Cable length 2 m (approx. 6.5 feet)
-
Features
- USB cable for connection between PC operator software and Motrona DS device
- USB connector type A on type B
- Length 1,8 m
-
Features
- USB cable for connection between PC and Motrona devices of the series IV/FU/PV/ZU210 and IP/FP/PP/ZP210
- USB connector type A on type Mini B
- Length 1,8 m
Page load link
