Skip to content
-
Features
- Incremental input with format A, /A, B, /B
- Differential, single-ended HTL / RS422
- Input frequency up to 1 MHz
- 3 control inputs for HTL / PNP signals
- Power supply 18 ... 30 VDC
- 24 V auxiliary output for encoder supply
- 3.78 x 1.89-inch norm panel housing and IP65 protection
- Bright and high-contrast display with event-dependent colour variations
- Emulation of a 7-segment display inclusively icons and units
- Intuitive and easy parameterization by plain text and touchscreen
- Multi-function device for use as speedometer/tachometer, pulse counter/position indicator, number counter and total counter
- Operating modes such as scaling, average filter, start-up suppression
- Linearization with 24 control points
Options
- Option AC: Power supply 115 ... 230 VAC
- Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
- Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
- Option CO: 4 control outputs, serial RS232 interface
- Option CR: 4 control outputs, serial RS485 interface
- Option RL: 2 relay outputs
Options can be combined.
-
Features
- Internal power supply 3,3 V
- Ambient temperature 0° C ... +60° C / 32° F ... 140° F (operating), -40° C ... +70° C / -40 ... 158° F (storage)
- 9600 Bit/s ... 12 MBit/s Baud rates
- SUB-D-9-pin female, galvanically isolated
-
Features
- Internal power supply 3,3 V
- Ambient temperature 0° C ... +60° C (operating), -40° C ... +70° C (storage)
- 100 MBit/s Vollduplex
- 2 Ethernet-Ports RJ45 with integrated switch, galvanically isolated
-
Features
- 1 connector Sub-D-9 (male)
- 1 connector Sub-D-9 (female)
- cable length 3 m (approx. 10 feet)
-
Features
- 1 encoder input with format SIN+, SIN-, COS+, COS-, REF+, REF- [1 Vss]
- Maximum sinus input frequency 500 kHz with max. 200 ns conversion time
- 4 signal outputs with format SIN+, SIN-, COS+, COS-, REF+, REF- [1 Vss]
- Power supply 17 ... 30 VDC
- Snap-on housing for top-hat rail (according to EN 60715)
-
Features
- USB cable for connection between PC and the Motrona unit UZ210
- Both connectors are type A
- Cable length 2 m (approx. 6.5 feet)
-
Features
- USB cable for connection between PC operator software and Motrona DS device
- USB connector type A on type B
- Length 1,8 m
-
Features
- USB cable for connection between PC and Motrona devices of the series IV/FU/PV/ZU210 and IP/FP/PP/ZP210
- USB connector type A on type Mini B
- Length 1,8 m
-
Features
- Pulse inputs A, B [HTL], A, / A, B, / B [RS422, HTL]
- SSI input in the format DATA +, DATA-, CLOCK +, CLOCK- up to 32 bits
- Start-stop interface for absolute transducers and magnetostrictive sensors
- 3 control inputs (hold) for PNP signals [10 ... 30 VDC]
- Input frequency up to 1 MHz
- 25-bit parallel output push-pull in BCD, binary or Gray code format
- Power supply 18 ... 30 VDC
- Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
-
Features
- Pulse inputs A, B [HTL], A, /A, B, /B [RS422, HTL]
- Input frequency up to 1 MHz [RS422], 200 kHz [HTL]
- Analog output ±10 V or 0/4 ... 20 mA, 16 Bit
- Power supply 18 ... 30 VDC
- Snap-on housing for top-hat rail (according to EN 60715)
- Setup via operator software OS6.0
- Serial RS232- / RS485 interface
- SSI input DATA+, DATA-, CLOCK+, CLOCK- [RS422], 32 Bit
- Start-stop interface for absolute transducers and magnetostrictive sensors
- USB interface and RS232/RS485 interface for configuration and serial readout
-
Features
- Hollow Shaft Small Size
- Resolution (Counts/Turn): 1,000∼12,000C/T
- Output Phase: A, B, Z, EU, EV, EW Phase
- Max Response Frequency: 200kHz
- Supply Voltage: DC+5V
- Consumption Current: 200mA Max
- Output Form: Line Driver
- Mounting Tolerance: Radial 0.05mm TIR Max, Axial 0.2mm Max, Shaft Runout 0.1°Max
- Starting Torque: 9.8×10-3N⋅m (100gf⋅cm Max)
- Protection: IP=40
- Operating Temp. Range: -20∼+85°C
- Vibration: 49m/s2(5G)
- Shock: 980m/s2(100G)
- Mass: 0.3kg Max
-
Features
- Hollow Shaft Small Size
- Resolution (Counts/Turn): 1,000∼12,000C/T
- Output Phase: A, B, Z, EU, EV, EW Phase
- Max Response Frequency: 200kHz
- Supply Voltage: DC+5V
- Consumption Current: 200mA Max
- Output Form: Line Driver
- Mounting Tolerance: Radial 0.05mm TIR Max, Axial 0.2mm Max, Shaft Runout 0.1°Max
- Starting Torque: 9.8×10-3N⋅m (100gf⋅cm Max)
- Protection: IP=40
- Operating Temp. Range: -20∼+85°C
- Vibration: 49m/s2(5G)
- Shock: 980m/s2(100G)
- Mass: 0.3kg Max
Page load link