Skip to content
Features
Very high-performance economical encoder
Low profile—25.4 mm height and 38 mm diameter
Thru-bore with sizes up to 10 mm
Simple, innovative flex mounting system (Global Mounting Standards)
Up to 12 pole commutation optional for brushless motor control
Features
Very high-performance economical encoder
Low profile—25.4 mm height and 38 mm diameter
Thru-bore with sizes up to 10 mm
Simple, innovative flex mounting system (Global Mounting Standards)
Up to 12 pole commutation optional for brushless motor control
Features
5mm Opto-ASIC encoder with a low profile (50.8mm)
Imperial bore sizes range from 0.625” to 1.125”
Metric bore sizes ranging from 6 mm to 28 mm
Single replacement solution for 50.8mm to 88.9mm encoders
Resolutions to 10,000 PPR, frequencies to 1 MHz
Versatile flexible mounting options
RoHS compliant
Corrosion-Resistant Option
Features
Low profile 30.3mm
Up to 12 pole commutation
Thru-bore and hollow-bore (blind) styles
Simple, innovative flexible mounting system
Incorporates Opto-ASIC technology
Features
Body: Precision Machined Aluminium
Cover: Precision Machined Aluminium (Powder Coated)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing - Rear: Single lip seal on the rear of cover
Protection: IP65
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM (Higher on request)
Torque: 2Ncm (typical)
Inertia: 100gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Body: Stainless Steel (316)
Cover: Stainless Steel (316)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing + Single lip seal
Rear: Single lip seal on the rear of the cover
Protection: (IP66 / IP67)
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM
Torque: 4Ncm (typical)
Inertia: 200gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Size 25 / 63.5mm Diameter (Hollow Shaft)
Up to 12 Pole Commutation Available
Thru Bore and Blind Bore Options
Simple, Innovative Flexible Mounting System
Incorporates Opto-ASIC Technology
Features
Thru-bore design for easy mounting
Bore options to 1.375" and 32mm
Incorporates Opto-ASIC technology
Resolutions to 4096 PPR
100° C operating temperature available
Features
Slim profile—only 34.5mm in depth
Thru-bore design for easy mounting
Incorporates Opto-ASIC technology
Resolutions to 4096 PPR
Bore options to 1.875" and 43mm
Features
Body: Precision Machined Aluminium
Cover: Precision Machined Aluminium (Powder Coated)
Shaft: Stainless Steel
Bearings: Ballraces
Shaft Sealing: Front: Sealed bearing
Rear: Single lip seal on the rear of the cover
Protection: IP65
Operating Temp: -20 to +60°C (Higher on request)
Maximum Speed: 3000 RPM (Higher on request)
Torque: 3Ncm (typical)
Inertia: 600gcm2 (typical)
Shaft Loading: Designed to support its weight
Cable: Screened, oil and salt waterproof
Impulse Frequency: Up to 300KHz (depending on model)
Current Consumption: 60mA (typical – without load)
Features
Number of output pulses per revolution 5.000 - 500.000 ppr
Line number on disc (z) 5.000
Maximum shaft speed 8000 rpm
The permissible motion of the shaft
- axial: ± 1.00 mm
- radial: 0.02 mm
Accuracy (T1-period lines on disc in arc. sec) ± 0.05T1 arc. sec
Starting torque at 20°C ≤ 0.01 Nm
Rotor moment of inertia < 20x10-4 kgm2
Protection (housing) (IEC 529) IP64
Protection (shaft side) (IEC 529) IP64
Maximum weight without cable 0.8 kg
Operating temperature -20...+70°C
Storage temperature -30...+85°C
Maximum humidity (non-condensing) 98%
Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
Permissible shock (11 ms) ≤ 300m/s²
Features
Number of output pulses per revolution 100-108000 ppr
Maximum shaft speed 10000 rpm
The permissible motion of the shaft
- axial: ± 0.5 mm
- radial: ± 0.05 mm
Accuracy (T1-period lines on disc in arc. sec) ± 0.1T1 arc. sec
Starting torque at 20°C ≤ 0.025 Nm
Rotor moment of inertia < 1.5x10-4 kgm2
Protection (housing) (IEC 529) IP64
Protection (shaft side) (IEC 529) IP64
Maximum weight without cable 0.3 kg
Operating temperature -10...+70°C
Storage temperature -30...+80°C
Maximum humidity (non-condensing) 98%
Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
Permissible shock (5 ms) ≤ 1000 m/s²
Features
6-wire connection for one strain gauge full bridge sensor
4 control inputs [HTL/PNP]
1 analog output ±10 V, 0/4 ... 20 mA, 16 bit
4 control outputs for signalling different operation states
Power supply 18 ... 30 VDC
Functions for scaling and linking the sensor signals (e.g. A+B, A-B, ...)
Adjustable bridge voltage per sensor from 3 VDC ... 10 VDC
Sensitivity of the sensor inputs 1 ... 10 mV
Transmission of the sensor data via RS485
Programming via USB and the user interface OS (freeware)
Protection class IP20
Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
Features
6-wire connection for two independent strain gauge full bridge sensors
4 control inputs [HTL/PNP]
2 independent analog outputs ±10 V, 0/4 ... 20 mA, 16 bit
4 control outputs for signalling different operation states
Power supply 18 ... 30 VDC
Functions for scaling and linking the sensor signals (e.g. A+B, A-B, ...)
Adjustable bridge voltage per sensor from 3 VDC ... 10 VDC
Sensitivity of the sensor inputs 1 ... 10 mV
Transmission of the sensor data via RS485
Programming via USB and the user interface OS (freeware)
Protection class IP20
Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
Features
Pulse input with format A, B, Z [HTL single-ended, TTL single-ended] or A, /A, B, /B, Z, /Z [RS422, HTL differential]
4 control inputs for HTL, PNP signals [10 ... 30 VDC]
Input and output frequency up to 1 MHz
3 incremental outputs with format A, /A, B, /B, Z, /Z, Push-Pull, [8 … 29 VDC]
Power supply 9 ... 30 VDC
Snap-on housing for top-hat rail (acc. EN 60715)
Multiplier/divisor adjustable as quotient F1 / F2
Multiplication/division without cumulative residual errors
Additional functions such as jog, trim, offset and reference
Features
Pulse input with format A, B, 90° [HTL] or A, /A, B, /B, Z, /Z [RS422]
4 control inputs for PNP signals [10 ... 30 VDC]
Input and output frequency up to 1 MHz
Pulse output with format A, /A, B, /B, Z, /Z and
push-pull characteristic, [5 ... 30 VDC]
Power supply 11 ... 30 VDC
Snap-on housing for top-hat rail (according to EN 60715)
LCD backlighted
Setup via keys, RS232
The device multiplies an incoming frequency by a proportional factor F1 and a reciprocal factor F2. The two factors F1 and F2 are adjustable in the range of 0.0005 to 9.9999
All operation modes provide error-free frequency conversion, with full consideration of the A / B phase and direction of the quadrature signals, therefore no cumulative errors, even with continuous changes of directions and vibrations
Zero pulse generator: the frequency multiplier generates at the output an index signal with an adjustable pulse interval, which can be synchronized as needed with the zero pulse at the input
Features
1 Strain gauge input
3 VDC and 10 VDC bridge voltage per sensor connection
1 … 10 mV sensitivity
optionally 3 control inputs for PNP signals [10 ... 30 VDC]
IO link interface
Power supply 12 ... 30 VDC
Compact housing for mounting on 35 mm DIN rail (according to EN 60715)
Features
Pulse input in format A, /A, B, /B, Z, /Z [RS422, HTL]
Pulse input in format A, B, Z [HTL]
Input frequency up to 1 MHz
Pulse output in format A, /A, B, /B, Z, /Z [RS422, HTL]
Pulse output in format A, B, Z [HTL]
Power supply 9 ... 30 VDC
Settings via DIL switches
Level conversion (RS422, HTL single-ended, HTL differential, TTL and vice versa)
Division of two-track A / B pulses with adjustable ratio 1: 1 to 1: 4096
Division of the Z pulse with adjustable ratio 1: 1 to 1: 256
External HTL signals for various functions
Implementation between the two types of representations for the direction of rotation (A / B 90 °, A/B Dir and vice versa, Division possible)
Snap-on housing for top-hat rail (acc. EN 60715)
Dimension (B x H X T) 22,5 x 102 x 102 mm
Features
4 pulse inputs with format A, /A, B, /B [RS422]
4 scalable 12-bit analog inputs for ±10 V or 0/4 ... 20 mA
8 control inputs for PNP signals [10 ... 30 VDC]
4 scalable 12-bit analog outputs for ±10 V or 0/4 ... 20 mA
Short loop time (depending on application)
Power supply 18 ... 35 VDC
Snap-on housing for top-hat rail (according to EN 60715)
Setup via Windows operator software (free of charge)
OnBoard interfaces: RS232 and CANopen
Features
Start-stop interface for absolute transducers and magnetostrictive sensors
SSI input in the format DATA +, DATA-, CLOCK +, CLOCK- up to 32 bits
3 control inputs (hold) for PNP signals [10 ... 30 VDC]
Pulse inputs A, B [HTL], A, / A, B, / B [RS422, HTL]
Input frequency up to 1 MHz
25-bit parallel output push-pull in BCD, binary or Gray code format
Power supply 18 ... 30 VDC
Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
Features
Start-stop interface for absolute transducers and magnetostrictive sensors
Adjustable frequency of the init pulses from 62.5 Hz to 5 kHz
Analog output ± 10 V, 0/4 ... 20 mA, 16 bit
Power supply 18 ... 30 VDC
Compact housing for mounting on a 35 mm top-hat rail (according to EN 60715)
Simple parameterization via the OS6.0 user interface
Serial RS232 / RS485 interface
Pulse inputs A, B [HTL], A, /A, B, /B [RS422, HTL]
SSI input DATA+, DATA-, CLOCK+, CLOCK- [RS422], 32 Bit
USB interface and RS232/RS485 interface for configuration and serial readout
Features
Pulse inputs A, B [HTL], A, / A, B, / B [RS422, HTL]
SSI input in the format DATA +, DATA-, CLOCK +, CLOCK- up to 32 bits
Start-stop interface for absolute transducers and magnetostrictive sensors
3 control inputs (hold) for PNP signals [10 ... 30 VDC]
Input frequency up to 1 MHz
25-bit parallel output push-pull in BCD, binary or Gray code format
Power supply 18 ... 30 VDC
Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
Features
Pulse inputs A, B [HTL], A, /A, B, /B [RS422, HTL]
Input frequency up to 1 MHz [RS422], 200 kHz [HTL]
Analog output ±10 V or 0/4 ... 20 mA, 16 Bit
Power supply 18 ... 30 VDC
Snap-on housing for top-hat rail (according to EN 60715)
Setup via operator software OS6.0
Serial RS232- / RS485 interface
SSI input DATA+, DATA-, CLOCK+, CLOCK- [RS422], 32 Bit
Start-stop interface for absolute transducers and magnetostrictive sensors
USB interface and RS232/RS485 interface for configuration and serial readout
Features
Hollow Shaft Small Size
Resolution (Counts/Turn): 1,000∼12,000C/T
Output Phase: A, B, Z, EU, EV, EW Phase
Max Response Frequency: 200kHz
Supply Voltage: DC+5V
Consumption Current: 200mA Max
Output Form: Line Driver
Mounting Tolerance: Radial 0.05mm TIR Max, Axial 0.2mm Max, Shaft Runout 0.1°Max
Starting Torque: 9.8×10-3N⋅m (100gf⋅cm Max)
Protection: IP=40
Operating Temp. Range: -20∼+85°C
Vibration: 49m/s2(5G)
Shock: 980m/s2(100G)
Mass: 0.3kg Max
Features
Wide temperature range
Superior environment resistance
Vibration: 196m/s2{20G} at 10Hz .500Hz, for 2 hours to each of three axes.
Shock: 981m/s2{100G} for 6ms, 3 times to each of 6 axes, 18 times in total
Humidity: 90% RH or above at 60°C
High-speed rotation
High reliability - Extremely long life and high reliability are assured by the structure of mechanical parts and automated coil incorporation.
Absolute position detection
Long-distance transmission - Robustness against noise enables long-distance transmission
Capable of compact incorporation - The use of built-in types of Smartsyn minimizes the housings of motors. Best suited for compact design
Low cost
Multipolarization is possible by increasing the multiplication factor of angle
Page load link